Difference between revisions of "Smartphones as ammeters"

From phyphox
Jump to navigation Jump to search
Line 10: Line 10:
 
==Requirements and experimental material==
 
==Requirements and experimental material==
  
- smartphone (with Phyphox and magnetic sensors)  
+
- smartphone (with phyphox-app and magnetic sensors)  
  
 
- a coil (more windings for finer readings)
 
- a coil (more windings for finer readings)
Line 16: Line 16:
 
==Introduction==
 
==Introduction==
 
Since the magnetic field induced in a coil by direct current is proportional to the current of the circuit, one can use this to indirectly measure amperage with the magnetic sensor of smartphone.  
 
Since the magnetic field induced in a coil by direct current is proportional to the current of the circuit, one can use this to indirectly measure amperage with the magnetic sensor of smartphone.  
 +
 +
Hence a coil of small diameter (in this example a custom wound coil of coated copper wire) is placed near the magnetic sensor of the smartphone. The .phyphox-file linked at the bottom allows the smartphone to convert the measured magnetic field into amperage after calibration.
  
 
==Calibration==
 
==Calibration==
 +
[[File:Interface_Kalibrierung.png|200px|thumb|right|figure 1: Interface for calibrating the sensor]]
 +
Since the relation of amperage and magnetic field of a coil are proportional to one another, a calibration via two data pairs of current and magnetic field is sufficient. Figure 1 shows the "Calibration"-page of the .phyphox-experiment. On this page the currently measured magnetic field is displayed and the two data pairs can be inserted.
  
 
==Examples==
 
==Examples==
 +
[[File:Interface_Anzeige.png|200px|thumb|right|figure 2: Interface for displaying measured current]]
 +
After calibrating the setup, the "display"-page can be opened. Here the measured current is displayed in numbrt- as well as graph-form, this page is shown in figure 2.
  
 
==Troubleshooting and Tipps==
 
==Troubleshooting and Tipps==
 +
 +
- One of the two data pairs needed for calibration can be acquired via measuring without current.
 +
 +
- The position of the coil is key: Moving the coil destroys the calibration. It is therefore recommended to fix the coil to the smartphone or mark the position of it.
 +
 +
- Moving the smartphone can also destroy the calibration since the influence of the earth's magnetic field can change.
 +
 +
- More accurate measurements can be acchieved by using coils with more windings, or inserting an iron core into the coil (the latter is of course only viable when measuring magnetic fields low enough to neglect the hystersis effect).

Revision as of 10:16, 19 March 2018

Smartphones as ammeters
Experiment Smartphones as ammeters
Category Magnetism
Used sensors magnetometer


With the help of this experiment the magnetic sensor of the smartphone can be used as an ammeter for direct current.


Requirements and experimental material

- smartphone (with phyphox-app and magnetic sensors)

- a coil (more windings for finer readings)

Introduction

Since the magnetic field induced in a coil by direct current is proportional to the current of the circuit, one can use this to indirectly measure amperage with the magnetic sensor of smartphone.

Hence a coil of small diameter (in this example a custom wound coil of coated copper wire) is placed near the magnetic sensor of the smartphone. The .phyphox-file linked at the bottom allows the smartphone to convert the measured magnetic field into amperage after calibration.

Calibration

figure 1: Interface for calibrating the sensor

Since the relation of amperage and magnetic field of a coil are proportional to one another, a calibration via two data pairs of current and magnetic field is sufficient. Figure 1 shows the "Calibration"-page of the .phyphox-experiment. On this page the currently measured magnetic field is displayed and the two data pairs can be inserted.

Examples

figure 2: Interface for displaying measured current

After calibrating the setup, the "display"-page can be opened. Here the measured current is displayed in numbrt- as well as graph-form, this page is shown in figure 2.

Troubleshooting and Tipps

- One of the two data pairs needed for calibration can be acquired via measuring without current.

- The position of the coil is key: Moving the coil destroys the calibration. It is therefore recommended to fix the coil to the smartphone or mark the position of it.

- Moving the smartphone can also destroy the calibration since the influence of the earth's magnetic field can change.

- More accurate measurements can be acchieved by using coils with more windings, or inserting an iron core into the coil (the latter is of course only viable when measuring magnetic fields low enough to neglect the hystersis effect).